for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 294 linear & power amplifiers - smt hmc590lp5 / 590lp5e v01.0107 general description features functional diagram the hmc590lp5 & hmc590lp5e are high dynamic range gaas phemt mmic 1 watt power amplifi ers which operate from 6 to 9.5 ghz. the amplifi er pro- vides 21 db of gain, +31 dbm of saturated power, and 23% pae from a +7welv supply. this 50 ohm matched amplifi er does not require any external components and the rf i/os are dc blocked for ro- bust operation. for applications which require op- timum oip3, idd should be set for 520 ma, to yield +40 dbm oip3. for applications which require optimum output p1db, idd should be set for 820 ma, to yield +30 dbm out-put p1db. electrical specifi cations, t a = +25 c, vdd = +7v, idd = 820 ma [1] typical applications the hmc590lp5 / hmc590lp5e is ideal for use as a power amplifi er for: ? point-to-point radios ? point-to-multi-point radios ? test equipment & sensors ? military end-use ? space parameter min. typ. max. min. typ. max. units frequency range 6 - 8 6 - 9.5 ghz gain 18 21 18 21 db gain variation over temperature 0.05 0.05 db/ c input return loss 15 12 db output return loss 11 10 db output power for 1 db compression (p1db) 27 30 27.5 30.5 dbm saturated output power (psat) 30.5 31 dbm output third order intercept (ip3) [2] 40 40 dbm supply current (idd) 820 820 ma [1] adjust vgg between -2 to 0v to achieve idd= 820 ma typical. [2] measurement taken at 7v @ 520ma, pin/tone = -15 dbm gaas phemt mmic 1 watt power amplifier, 6.0 - 9.5 ghz saturated output power: +31.5 dbm @ 23% pae output ip3: +40 dbm gain: 21 db dc supply: +7v @ 820 ma 50 ohm matched input/output qfn leadless smt packages, 25 mm 2
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 295 hmc590lp5 / 590lp5e v01.0107 gaas phemt mmic 1 watt power amplifier, 6.0 - 9.5 ghz input return loss vs. temperature output return loss vs. temperature broadband gain & return loss gain vs. temperature p1db vs. temperature psat vs. temperature -25 -20 -15 -10 -5 0 5 10 15 20 25 30 456789101112 s21 s11 s22 response (db) frequency (ghz) -25 -20 -15 -10 -5 0 456789101112 +25c +85c -40c return loss (db) frequency (ghz) 25 27 29 31 33 35 6 6.5 7 7.5 8 8.5 9 9.5 10 +25c +85c -40c psat (dbm) frequency (ghz) 25 27 29 31 33 35 6 6.5 7 7.5 8 8.5 9 9.5 10 +25c +85c -40c p1db (dbm) frequency (ghz) -35 -30 -25 -20 -15 -10 -5 0 456789101112 +25c +85c -40c return loss (db) frequency (ghz) 8 12 16 20 24 28 6 6.5 7 7.5 8 8.5 9 9.5 10 +25c +85c -40c gain (db) frequency (ghz)
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 296 linear & power amplifiers - smt v01.0107 power compression @ 8 ghz, 7v @ 820 ma output ip3 vs. temperature 7v @ 520 ma, pin/tone = -15 dbm output im3, 7v @ 520 ma output im3, 7v @ 820 ma 0 20 40 60 80 -20 -16 -12 -8 -4 0 4 8 6 ghz 7 ghz 8 ghz 9 ghz 10 ghz im3 (dbc) pin/tone (dbm) 0 5 10 15 20 25 30 35 -14 -10 -6 -2 2 6 10 14 pout gain pae pout(dbm), gain (db), pae(%) input power (dbm) 0 20 40 60 80 -20 -16 -12 -8 -4 0 4 8 6 ghz 7 ghz 8 ghz 9 ghz 10 ghz im3 (dbc) pin/tone (dbm) 26 30 34 38 42 46 6 6.5 7 7.5 8 8.5 9 9.5 10 +25c +85c -40c ip3 (dbm) frequency (ghz) psat vs. current p1db vs. current 25 27 29 31 33 35 6 6.5 7 7.5 8 8.5 9 9.5 10 520ma 620ma 720ma 820ma psat (dbm) frequency (ghz) 25 27 29 31 33 35 6 6.5 7 7.5 8 8.5 9 9.5 10 520ma 620ma 720ma 820ma p1db (dbm) frequency (ghz) gaas phemt mmic 1 watt power amplifier, 6.0 - 9.5 ghz hmc590lp5 / 590lp5e
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 297 v01.0107 reverse isolation vs. temperature, 7v @ 820 ma power dissipation -80 -70 -60 -50 -40 -30 -20 -10 0 6 6.5 7 7.5 8 8.5 9 9.5 10 +25c +85c -40c isolation (db) frequency (ghz) gain & power vs. supply current @ 8 ghz gain & power vs. supply voltage @ 8 ghz 18 20 22 24 26 28 30 32 34 6.5 7 7.5 gain p1db psat gain (db), p1db (dbm), psat(dbm) vdd supply voltage (vdc) 16 20 24 28 32 36 940 1140 1340 gain p1db psat gain (db), p1db (dbm), psat(dbm) idd supply current (ma) 3 3.5 4 4.5 5 5.5 6 -14 -10 -6 -2 2 6 10 14 6 ghz 7 ghz 8 ghz 9 ghz 10 ghz power dissipation (w) input power (dbm) electrostatic sensitive device observe handling precautions gaas phemt mmic 1 watt power amplifier, 6.0 - 9.5 ghz absolute maximum ratings drain bias voltage (vdd) +8 vdc gate bias voltage (vgg) -2.0 to 0 vdc rf input power (rfin)(vdd = +7.0 vdc) +12 dbm channel temperature 175 c continuous pdiss (t= 75 c) (derate 59.8 mw/c above 75 c) 5.98 w thermal resistance (channel to package bottom) 16.72 c/w storage temperature -65 to +150 c operating temperature -55 to +85 c vdd (v) idd (ma) +6.5 824 +7.0 820 +7.5 815 typical supply current vs. vdd note: amplifi er will operate over full voltage ranges shown above vgg adjusted to achieve idd = 820 ma at +7.0v hmc590lp5 / 590lp5e
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 298 linear & power amplifiers - smt v01.0107 notes: 1. leadframe material: copper alloy 2. dimensions are in inches [millimeters] 3. lead spacing tolerance is non-cumulative 4. pad burr length shall be 0.15mm maximum. pad burr height shall be 0.05mm maximum. 5. package warp shall not exceed 0.05mm. 6. all ground leads and ground paddle must be soldered to pcb rf ground. 7. refer to hittite application note for suggested land pattern. part number package body material lead finish msl rating package marking [3] hmc590lp5 low stress injection molded plastic sn/pb solder msl1 [1] h590 xxxx hmc590lp5e rohs-compliant low stress injection molded plastic 100% matte sn msl1 [2] h590 xxxx [1] max peak refl ow temperature of 235 c [2] max peak refl ow temperature of 260 c [3] 4-digit lot number xxxx package information outline drawing gaas phemt mmic 1 watt power amplifier, 6.0 - 9.5 ghz hmc590lp5 / 590lp5e
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 299 v01.0107 pin descriptions pin number function description interface schematic 1, 2, 6 - 19, 23, 24, 26, 27, 29, 31 n/c not connected. 3, 5, 20, 22 gnd these pins and package bottom must be connected to rf/dc ground. 4rfin this pad is ac coupled and matched to 50 ohms. 21 rfout this pad is ac coupled and matched to 50 ohms. 25, 28, 30 vdd 1-3 power supply voltage for the amplifi er. external bypass capacitors of 100 pf and 2.2 f are required. 32 vgg gate control for amplifi er. adjust to achieve idd of 820 ma. please follow mmic amplifi er biasing procedure application note. external bypass capacitors of 100 pf and 2.2 f are required. gaas phemt mmic 1 watt power amplifier, 6.0 - 9.5 ghz hmc590lp5 / 590lp5e
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com 11 11 - 300 linear & power amplifiers - smt v01.0107 gaas phemt mmic 1 watt power amplifier, 6.0 - 9.5 ghz application circuit component value c1 - c4 100pf c5 - c8 2.2f hmc590lp5 / 590lp5e
for price, delivery, and to place orders, please contact hittite microwave corporation: 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com linear & power amplifiers - smt 11 11 - 301 v01.0107 gaas phemt mmic 1 watt power amplifier, 6.0 - 9.5 ghz evaluation pcb the circuit board used in the fi nal application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and package bottom should be connected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation board should be mounted to an appropriate heat sink. the evaluation circuit board shown is available from hittite upon request. list of materials for evaluation pcb 115927 [1] item description j1 - j2 pcb mount sma connector j3 dc pin c1 - c4 100 pf capacitor, 0402 pkg c5 - c8 2.2 f capacitor, 1206 pkg u1 hmc590lp5 / hmc590lp5e pcb [2] 109001 evaluation pcb [1] reference this number when ordering complete evaluation pcb [2] circuit board material: rogers 4350 hmc590lp5 / 590lp5e
|
